Some commercial cleaners may damage the plastic parts. Room Cabinet and Case Turn the Zoneline off and disconnect the To clean, use water and a mild detergent. Safety Instructions Operating Instructions Care and Cleaning Troubleshooting Tips Consumer Support Care and cleaning. A separate wire pair must be run from each separate controlling switch to each individual Zoneline. Central Desk Control When connected, the unit can be turned ON or OFF with a switch located at the Central Control Panel. Connections provide 24 V AC to energize a remote relay, turning on the external fan. External Fan (Obtained locally) When connected, an auxiliary or external fan can be controlled with the indoor fan motor on the Zoneline. This increases the fan speĪuxiliary controls on your Zoneline. If the unit is ducted, the Duct Mode the display.
![how to install peltor arc rail adapter how to install peltor arc rail adapter](https://www.365-plus.com/productimg/rail-adapter-kit-for-helmet-fits-arc-peltor-3m-gal12808-big.jpg)
Pressing MODE on Model AZ4100 will This setting is used when the unit is installed using a return you to AUX SET mode and an “AU” will appear in duct adapter kit. For Model AZ6100, press MODE to continue setting other functions. Safety Instructions Operating Instructions Care and Cleaning Troubleshooting Tips Consumer Support MODE 7 Duct Mode The default setting for Mode 7 is OFF. Press the down LOW FAN arrow for OFF " " or the
![how to install peltor arc rail adapter how to install peltor arc rail adapter](https://sep.yimg.com/ay/optacticalgear/unity-tactical-mark-kit-4.jpg)
The HIGH COOL HEAT LED light on the main control will be on. Press MODE again to change to the Heat Sentinel. The COOL LED light on the main control Freeze Sentinel OFF will be on. LOW FAN Press MODE until a 3 appears in the first digit of the display for AUTO HEAT Freeze Sentinel mode. Freeze Sentinel/Heat Sentinel MODE 3 HIGH COOL In the default setting for Mode 3, Heat Sentinel is off, Freeze Sentinel is on. There are 9 different modesĪuxiliary controls on your Zoneline. The owner is responsible for ensuring the auxiliary controls are set to the desired function. See the To Remove the Room Cabinet section. Auxiliary Set Button Auxiliary Controls-Aux Set Button The auxiliary set controls are located behind the room cabinet, below the control panel. Safety Instructions Operating Instructions Care and Cleaning Troubleshooting Tips Consumer Support Auxiliary controls on your Zoneline. When set at the closed position, only the air inside the room is circulated and filter The ventilation control lever is located at the middle left side of the Zoneline unit, behind the room cabinet. If you do not plan to use the ventilation feature, leave these two screws in place. See the Installation Instructions in the back of this manual. Closed Ventilation Control Open position position NOTE: Two shipping screws must be removed from the vent door before use. When set at AUTO, and off to keep the room at the same level it automatically switches between LOW of comfor The compressor will cycle on LOW or AUTO speed. TEMP CONTROL FAN, MODE & SLEEP OPERATION Controls Temp Control Fan, Mode and Operation Control The temp control is used to maintain the room FAN-Sets the fan operation for HIGH, temperature. Safety Instructions Operating Instructions Care and Cleaning Troubleshooting Tips Consumer Support About the controls on your Zoneline. SAFETY PRECAUTIONS This Zoneline must be properly installed These R410A air conditioning systems in accordance with the Installation require contractors and technicians to Instructions before it is used.
HOW TO INSTALL PELTOR ARC RAIL ADAPTER MANUAL
WARNING! For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric shock, or to prevent property damage, personal injury, or loss of life. 4 Español For a Spanish version of this Care and Cle 4 Heat/Cool Model 4100 Auxiliary Controls. 2 Owner’s Manual and Installation Instructions Operating Instructions Air Direction. The aggressive wire forms ensure the strongest ear cup seal when engaged.Ĭonstructed of impact-resistant polymer, the MARK 2.0 is designed for use in the most austere Safety Instructions. Rather than using a traditional pop-in/pop-out mechanism, MARK2.0 is simply pulled away from the ears and rotated backwards for stowage. MARK 2.0 is the lowest profile headset helmet mount on the market. The wider ARC™ backers allow for more compatibility with non-standard ARC-type rails than the previous model. An M-LOK™ Adapter Kit is sold separately for compatibility with MTEK and Hard Head Veterans brand helmets. The MARK 2.0 Kit comes with all hardware for attachment to Ops-Core ARC™ (and similar) and Team Wendy EXFIL™ Gen 2 and 3 rails. If attaching to Sordin/MSA™ style headsets, use the SARA Adapters (sold separately). The MARK 2.0 Kit will work with 3M Peltor™ Headsets right out of the package.
![how to install peltor arc rail adapter how to install peltor arc rail adapter](http://atairsoftgear.com/image/cache/data/Products/at-acc37-bk-04-800x800.jpg)
The MARK 2.0 is compatible with most major helmet types and the most popular electronic hearing protection. The Modular Attached Rail Kit (MARK) 2.0 allows the end user to seamlessly integrate their hearing protection and/or integrated communications into their headborne systems and improve the consistent seal of ear protection.